KUAT TEKAN BETON CAMPURAN GGBFS DAN FLY ASH MENGGUNAKAN RETARDER

Anni Susilowati, Iqbal Yusra

Abstract


Abstract One of the world's construction needs is casting in large volumes that require concrete with low hydration heat, and one of the problems is that the concrete has a setting during the casting queue. Therefore, a research was conducted on adding retarder to concrete with a mixture of GGBFS and Fly Ash. The purpose of this research was to analyze the physical and mechanical properties of concrete, the effect of adding retarder and obtain optimal retarder levels. This research used an experimental methods to make concrete specimens of 75% cement mix: GGBFS 15%: Fly Ash 10% with a water cement ratio of 0.5 using mix design SNI-03-2834-2000. Variations of the retarder added to the concrete mixture were 0%, 0.2%, 0.4%, and 0.6% by weight of cement with the Naptha RD 31 type. Analysis of the effect of the retarder used statistical regression test methods on SPSS. The results of research obtained the longest setting time in this researchwas 1890 minutes at a variation of 0.6% with a slump of 168 mm. The compressive strength of the concrete increased by 12.07% - 52.36% by using a retarder added material. Based on the research results, it was obtained that the optimum level of use of retarder in mixed concrete GGBFS and Fly Ash was 0.2% because it has the best physical and mechanical properties. Keywords: Fly Ash, GGBFS, Compressive Strength, Retarder

Full Text:

PDF

References


Daftar Rujukan

Topcu, I.B. (2013). “High Volume Ground

Granulated Blast Furnace Slag

Concrete.” Eco-Efficient Concete, 218–

https://doi.org/10.1553/9780857098

2.2 18.

Krakatau Semen Indonesia, PT. n.d. “Ground

Granulated Blast Furnace Slag.”

http://krakatausemenindonesia.com/

blastfu rnaceslag.

Prayogo. A. (2019). “GGBFS Dan Fly Ash

Sebagai Subtitusi Sebagian Semen Pada

Beton,” Politeknik Negeri Jakarta.

Anshar, Dkk. (2018) “Panas Hidrasi Beton

Massa yang Menggunakan Semen

Portland Komposit,” Universitas

Hasanudin

B. Setiawan and F.X. Supartono. (2018).

“Analisis Heat Transfer pada Beton

Massa Menggunakan OPC Tipe I dalam

Hubungan dengan Cara Curing.”

Universitas Tarumanagara.

American Concrete Insitute (ACI) .224.1.R937,

ACI.Jurnal Vol. 94. No. 2.1997,ACI 207

& ACI 305

Sabrina, et al. (2017). “Kajian Pengaruh Variasi

Penambahan Bahan Retarder Terhadap

Parameter Beton Memadat Mandiri

Dengan Kuat Tekan Beton Mutu Tinggi.”

Universitas Sebelas Maret.

Nurfitriani, N. & Wibawa, T. (2019). “Kualitas

Beton Normal Dengan Penambahan

Retarder.” Politeknik Negeri Jakarta.

Badan Standarisasi Nasional. (2011). SNI 1974-

“Cara Uji Kuat Beton Dengan

Benda Uji Silinder.” Jakarta:BSN

Maricarr, S., Tatong, B., & Hasan, H. (2013).

“Pengaruh Bahan Tambah PlastimentVz

terhadap Sifat Beton.” Universitas

Tadulako.




DOI: http://dx.doi.org/10.33795/prokons.v15i1.281

Refbacks

  • There are currently no refbacks.


Copyright (c) 2021 Anni Susilowati, Iqbal Yusra

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

INDEXING : 

The following is an indexing list that includes the journal of the Prokons, published by the Civil Engineering Department, Politeknik Negeri Malang

    

    

_______________________________________________________________________________________________

Jurusan Teknik Sipil Politeknik Negeri Malang

Jalan Soekarno-Hatta No. 09, PO BOX 04 Malang 65141

Telp 0341-404424 || Fax 0341-404420

ISSN Print(1978-1784) || Online(2714-8815)

Email : prokons@polinema.ac.id

 

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.